Hardware Specifications

Modifying firmware

The Nokia G-010S-A can be flashed with the Nokia G-010S-P firmware, provided the MTD layout has been changed beforehand to match the new one. For the full procedure, see this post on lafibre.info

List of software versions

• https://github.com/hwti/G-010S-A/tree/main/firmwares

Serial

The stick has a TTL 3.3v UART console (configured as 115200 8-N-1) that can be accessed from the SFP connector.

List of partitions

List of software versions

• 3FE46398AFGA95
• 3FE46398AFGB89
• 3FE46398BFGA06
• 3FE46398BFGB18
• 3FE46398BFIB36
• 3FE46398BGCB22
• 3FE47111AFGB89
• 3FE47111BFHB32

See more info on: Firmwares G-010S-A

Usage

Enabling serial

fw_setenv bootdelay 5
fw_setenv asc0 0
fw_setenv preboot

GPON ONU status

Getting the operational status of the ONU

onu ploamsg

Getting information on the OLT vendor

omci_pipe.sh meg 131 0

Querying a particular OMCI ME

omci_pipe.sh meg MIB_IDX ME_IN

Where MIB_IDX is the MIB ID and ME_IN is the ME instance number

Getting/Setting Speed LAN Mode

To enable the interface to sync at 2.5 Gbps speeds / using HSGMII with auto-neg on:

fw_setenv sgmii_mode 5

To revert the change back to default:

fw_setenv sgmii_mode

To get the (H)SGMII Mode:

onu lanpsg 0

The link_status variable tells the current speed

GPON/OMCI settings

Enabling parameter modification

This setting must be set in order to perform other parameter modifications

ritool set OperatorID 0000

Getting/Setting ONU GPON Serial Number

To check the current serial number:

onu gtcsng

To set the current serial number:

ritool set MfrID ABCD
ritool set G984Serial 012345678
ritool set YPSerialNum 012345678

Getting/Setting ONU GPON PLOAM password

To check the current password (the password field contains decimal values of ASCII characters):

onu gtccg

This value can be changed using the web interface.

Getting/Setting OMCI software version (ME 7)

The software version must be changed by directly modifying firmware by using the patches found in the wiki’s page about the Nokia G-010-A ONT and then adding a folder 0001_swversion that contins a file patch.sh with the following content:

#!/bin/sh

set -e

ROOTFS=$1

echo "Changing to software version desidered"
sed -i s/3FE46398BGCB22/3FE45655BOCK99/g "$ROOTFS/usr/etc/buildinfo"

Where 3FE46398BGCB22 is the current software version and 3FE45655BOCK99 the desired software version

Getting/Setting OMCI hardware version (ME 256)

ritool set HardwareVersion 3FE47211EGAA
ritool set ICS 01

Getting/Setting OMCI equipment ID (ME 257)

This ONT is designed to save Nokia’s equipment ID, specifically to set the equipment ID of a Nokia G-010G-Q the following commands are to be used:

ritool set CleiCode __________
ritool set Mnemonic G-010G-Q__

Where CleiCode is the prefix and Mnemonic the postfix.

Advanced settings

Transferring files to the stick

# scp rootfs.bin root@192.168.1.10:/tmp/

Backup of all partition

Make a backup of all partitions, an easy way is to run these commands:

• On the stick run:

  cat /proc/mtd
  

• For each mtdX run this command in the lantiq shell:

  cp /dev/mtdX /tmp
  

And in the computer shell:

scp ONTUSER@192.168.1.10:/tmp/mtdX ./

Checking the currently active image

upgradestatus

Setting management MAC

ritool set MACAddress 12:34:56:78:9A:BC

Setting management IP

ifconfig eth0:1 192.168.1.10 netmask 255.255.255.0

Flashing a new rootfs via SSH

The following commands are used to flash a new rootfs to image1 and then boot to it:

mtd write /tmp/rootfs.bin image1
update_env_flag 1
reboot

Disabling Dying Gasp

uci set gpon.gtc.nDyingGaspEnable='0'; uci commit gpon

Rebooting the ONU

reboot

Miscellaneous commands

cat /configs/image_version
cat /usr/etc/buildinfo
ritool dump
omciMgr

Miscellaneous Links

• G-010S-A
• Usage GPON module SFP in Spain
• Bypassing the HH3K up to 2.5Gbps using a BCM57810S NIC
• Nokia G-010S-A Pin 6 Iusse - Rsaxvc.net
• Might require solder mod in order to work with BCM57810S NIC