Root Procedure for Huawei MA5671A (V3 - Web serial)

Can be accessed via the link Web root procedure

Root Procedure for Huawei MA5671A (V2 - Python)

1. Take the SFP molex and four coloured cables and solder them to the molex according to the following diagram:

1. Install python and pyserial with pip

   pip install pyserial
   

2. Make the connections as shown to a TTL adapter except for GND (which should remain detached as it is used as a switch)

1. Open Tera Term (or other serial terminal emulators), find the correct serial port of the TTL adapter, change the port on the script on line 7 instead of COM8.
2. After this, run the following python script and connect the GND pin:

import sys
import time

import serial.tools

try:
    ser = serial.Serial("COM8", 115200, parity=serial.PARITY_NONE, stopbits=serial.STOPBITS_ONE, bytesize=serial.EIGHTBITS)
    print('[+] Use serial port device:', ser.name)
    print('[+] Waiting for trigger characters...')
    while True:
        try:
            recv = ser.readline().decode()
        except Exception as x:
            print("Decode errore", x)
            continue
        if recv.startswith('U-Boot'):
            print('[+] Received! transfer enable command...')
            print('[+] Transfer command sequence 1')
            t_end = time.time() + 3
            while time.time() < t_end:
                ser.write(chr(3).encode())
            time.sleep(1)
            print('[+] Transfer command sequence 2')
            ser.write('setenv bootdelay 3\n'.encode())
            time.sleep(1)
            print('[+] Transfer command sequence 3')
            ser.write('setenv asc0 0\n'.encode())
            time.sleep(1)
            print('[+] Transfer command sequence 4')
            ser.write('setenv preboot "gpio set 3;gpio input 2;gpio input 105;gpio input 106;gpio input 107;gpio input 108"\n'.encode())
            time.sleep(1)
            print('[+] Transfer command sequence 5')
            ser.write('saveenv\n'.encode())
            time.sleep(3)
            print('[+] Transfer command sequence 6')
            ser.write('reset\n'.encode())
            print('[+] Enable command transfer complete! rebooting...')
            break
        else:
            print(recv)
except Exception as e:
    try:
        print('[!] Error:', e)
        sys.exit(1)
    finally:
        e = None
        del e

except (KeyboardInterrupt, SystemExit):
    ser.close()
    sys.exit(1)

1. Reboot the stick
2. Open Tera Term (or other serial terminal emulators), after it has loaded press enter to activate the console

1. With sed change the default shell from /opt/lantiq/bin/minishell to /bin/ash by editing the file /etc/passwd:

sed -i  "s|/opt/lantiq/bin/minishell|/bin/ash|g" /etc/passwd

[   34.612000] Kernel panic - not syncing: Fatal exception in interrupt
[   34.612000] Rebooting in 3 seconds..

After this is done, reboot the stick, after connecting it to a router via an ethernet mediaconverter or directly plugging it in an SFP port, with the port’s IP set to any IP of the 192.168.1.0/24 subnet (the stick has the IP 192.168.1.10)

1. Run the terminal and login to the stick with ssh

ssh root@192.168.1.10

The password is admin123.

Root Procedure for Huawei MA5671A (V1 - Tweezers)

1. Take the SFP molex and the 4 coloured cables and solder them to the molex according to the following diagram:

1. Disassemble the stick by releasing the metal tabs that hold the cover in place. There are two tabs, one on each side, inside these holes:

1. Once you have removed the metal casing, you are left with the half-naked stick. Note that the release mechanism also comes off easily, so it is recommended to take a photo and to memorise the positioning to be able to put it back together in the case it does come off.

2. Before shorting the stick, connect the previously soldered cables and molex to the USB serial (photo immediately below) and to the stick (via the molex, of course) and check that the jumper on the usb key is set to 3.3V

1. The disassembled stick will appear as in the photo: the two pins to be shorted are highlighted in red. In the photo below a wire is used, but a pair of tweezers is sufficient (I used those, in fact). Be careful not to touch anything around the two pins by possibly covering everything else with electrical tape.

1. For the moment connect all cables to the usb key except the green (ground) or red (voltage), otherwise the stick will boot before you can do the following (N.B. for those who bought the uart above RX and TX are reversed). Open and configure Tera Term for serial connection by selecting the correct com port, speed 115200 bauds, english language (otherwise in japanese you can’t read anything understandable), then insert the key in the PC (the adapter being already installed is taken for granted), short the 2 pins seen above and, while keeping the pins shorted, connect the missing coloured cable

2. If nothing happens, you have obviously done something wrong with cables, molexes, soldering irons, etc., so you will have to start from the beginning again and work out which step you did wrong. If you have done everything correctly, you should see something similar to the picture below:

1. Remove the short (tweezers or whatever you used), then type 7 and enter. You should see this:

1. From the Tera Term menu FILE → TRANSFER → XMODEM → SEND → [1224abort.bin] (which is the third of the files downloaded earlier):

1. As soon as the file transfer is complete, you have 2 seconds to press CTRL+C. If you have not done so, return to step 6. Otherwise, you should see:

1. To permanently unlock the bootloader, without having to repeat the previous steps, you must give the following commands:

   FALCON => setenv bootdelay 5
   FALCON => setenv asc0 0
   FALCON => setenv preboot "gpio set 3;gpio input 100;gpio input 105;gpio input 106;gpio input 107;gpio input 108"
   FALCON => saveenv
   

1. If you have done everything correctly you can reboot the stick (if you are convinced that everything is ok you could also close it again), disconnect and reconnect either the ground or voltage cable, then again you will have 5 seconds to lock the bootloader by doing a simple CTRL+C using the terminal. Now upload the firmware image of the first mtd2 partition to the stick with the command

   FALCON => loadb 0x80800000
   

   At this point it will appear:

1. From the Tera Term menu do FILE → TRANSFER → KERMIT → SEND → [mtd2.bin]. It will start uploading the file at a speed of about 3-4 KBps: it should take more than half an hour for the upload to complete.

2. Once finished, the image loaded on the stick must also be saved to the corresponding system partition (the first of the 2) with the commands

   FALCON => sf probe 0
   FALCON => sf erase C0000 740000
   FALCON => sf write 80800000 C0000 740000
   

3. Check that the stick is configured to boot from partition 0 (We are aware that mtd2 goes on 0 and mtd5 goes on 1, complain to Lantiq about this) with the command:

   FALCON => printenv committed_image
   

4. If it is 0 there’s no need to do anything, otherwise configure the stick to boot from partition 0 with the following commands, then check if the settings were changed correctly.

   FALCON => setenv committed_image 0
   FALCON => saveenv
   FALCON => printenv committed_image
   

Miscellaneous Links

• Come avere i 2.5 Gbps su un unico dispositivo senza il Fastgate
• Support MA5671A SFP GPON
• La fibre Orange à 2Gbps, sur un routeur MikroTik 10Gbps CCR2004, via un ONT SFP+
• Bypassing the HH3K up to 2.5Gbps using a BCM57810S NIC